What did you do to your rig today?

Post by **Incognito27** » Mon Aug 01, 2016 7:55 pm

Did my 2" lift kit on the 15 Xterra , AAL on the back and In Coil spacer for the fronts , however i boo booed on the fronts so looking to replace them

Post by **Snafu** » Mon Aug 01, 2016 10:48 pm

How boo-boo'd?

All four corners got new stuff on today. Cleaned up underneath (blasted some, painted others, rust-proofed hard to reach areas). Took a while but it looks good. Let's hope it stops.

SMOD mod for another day

Post by **Incognito27** » Mon Aug 01, 2016 11:24 pm

Snafu wrote:How boo-boo'd?

All four corners got new stuff on today. Cleaned up underneath (blasted some, painted others, rust-proofed hard to reach areas). Took a while but it looks good. Let's hope it stops.

SMOD mod for another day

Both Nuts that compress the Strut top hat and spring are seized on and can not come off . Not sure how as we didn't cross thread them on , i assume that they jumped a thread while under pressure from the spring and that cross threaded them.

Bright side , i have a S model , i ordered a set of Bilstein 4600 Struts should be here thursday and install friday at the latest

Post by **BigRed44** » Tue Aug 02, 2016 2:41 pm

Kicked the tires and nothing fell off

Post by **Snafu** » Tue Aug 02, 2016 3:26 pm

Drove the truck to work and it stopped...a good sign.

Post by **Drizit** » Tue Aug 02, 2016 3:31 pm

Looked at it funny, all the tires have air still... I say it's good for NL.

Post by **Miner** » Wed Aug 03, 2016 9:25 am

Replaced all four leaf spring packs, and rebushed the equalizer bars on the travel trailer suspension. The orginal springs were starting to defrom "plastically", espescially the right rear. The springs were starting to look like w's not u's. Job went well, impact made removing the old hardware much easier and only one spring bolt stripped.

Greased the hubs before reinstalling the tires, checked it over and its ready for our road trip.

Post by **sandor** » Mon Aug 15, 2016 10:48 pm

Makin' beadlocks

Post by **Drizit** » Tue Aug 16, 2016 12:18 am

Nice, you will love the preformance change a lower pressure makes.

Post by **Snafu** » Tue Aug 16, 2016 11:33 am

Those are nice.

I am hoping to get new leafs in the rear this weekend. Anyone wanna come over?

Also trying my hand at making a cargo net. Turning out good so far. It is giving me ideas to make one for the roof rack too and perhaps custom orders for friends

Post by **sandor** » Tue Aug 16, 2016 3:50 pm

I was already running single digit pressures on non-beadlock rims, however rocks were killing my rims. Since I needed at least one new rim, and wanted to protect against future rock damage, went with beadlocks as opposed to rim stiffners, and now I have the option of going even lower into single digits.

Post by **Morpheus** » Tue Aug 16, 2016 4:22 pm

Ordered parts to repair NL carnage.

Post by **Bow_Tied** » Tue Aug 16, 2016 4:23 pm

Morpheus wrote:Ordered parts to repair NL carnage.

Details required.

Post by **Morpheus** » Tue Aug 16, 2016 4:33 pm

So far a rebuild kit from TotalChaos in California, and maybe upper control arm bushings from 4x4 parts in Florida.

I might have a couple spare bushings that were still good from the last time I rebuilt the control arms. Need to check my toolbox tonite.

Post by **Bow_Tied** » Tue Aug 16, 2016 4:34 pm

Carnage details!

what happened? And is there video footage?

Post by **Snafu** » Tue Aug 16, 2016 5:30 pm

Again? If you had a 2nd gen then I might have some parts for you.

Post by **Drizit** » Tue Aug 16, 2016 6:10 pm

There is video of me ripping apart my shock from 2 angles. I just have to bug the ppl who took it to upload it.

Post by **sandor** » Tue Aug 16, 2016 7:09 pm

I am sure you are after Mike's carnage details and video, but while you are waiting for his, here's mine from a few weeks ago.

Running 8-9 PSI in the tires, second half of the footage, repeated attempts at where the video ends resulted in collateral damage to the right rear rim...lip folded in, sounded like a compressed air nozzle, beat it back into position with a sledge, but it was never the same...air leaks from four different places on the outside lip from multiple hits to the same rock due to multiple attempts trying to get through the gap. Ended up winching...with a flat...until we put the spare on mid hill...then still had to winch. Nissan t-case gearing is not low enough for that type of hill climb, and clutch was starting to smell.

https://youtu.be/QBjnhhQ-qTM

Hence the need for beadlocks...that flat tire ruined the climb for me.

Post by **Snafu** » Tue Aug 16, 2016 8:21 pm

Did you ever change the axle gear ratios with the taller tires? Just curious

Post by **sandor** » Tue Aug 16, 2016 9:34 pm

I didn't, but the guy who built it put 5.38s in there; speedo is off by less than 5%. I don't think axle gearing is the issue, as it drives alright in high range. Low range just isn't low enough for crawling boulders...plus it's a heavy bugger.

Canadian Nissan Truck Club

What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Connect with your social network account