What did you do to your rig today?

Post by **bluesrebel** » Thu Mar 06, 2014 8:34 pm

Yeah, we hope to get out a lot more this year.

Got new 32" KM2's yesterday & also ordered shrock sliders

Post by **Bow_Tied** » Sat Mar 08, 2014 8:42 pm

OOooh, KM2s, nice. jealous

Serviced all four calipers on the Z today as well as a front end grease. I see one of the original upper ball-joints has a ripped boot. Nice.

Post by **Miner** » Sun Mar 09, 2014 9:00 pm

Calipers pads and rotors stripped from the Maxima donor car. Calipers serviced, rotors buffed, and installed on the Maxima project car. Also removed bug deflector, "patched" flex pipe, checked codes, replaced wipers, started on rust projects, and cleaned up the filler neck on the project car.

Swapped the snow tires too. Lots of snow in the forecast, almost forgot it was march when looking at the weather network.

Post by **Adam** » Mon Mar 10, 2014 7:51 pm

Crazy smarch weather!!

Post by **Miner** » Tue Mar 11, 2014 9:18 am

More rust work...need some body work materials.

Cleaned the RAVEs on the Renegade, pulls hard to ~7700rpm now.

Post by **lookzcustoms** » Tue Mar 11, 2014 10:07 am

installed spacers, will take better pics today

after

Post by **Nd4SpdSe** » Tue Mar 11, 2014 10:35 pm

Met my parents in Kingston for the weekend + Monday. Did the usual stop at PA and picked up some lights for the roof and some 0/1 gauge disconnects and a 7-pin trailer harness that I'll install in the new bumper.

Post by **Miner** » Wed Mar 12, 2014 8:50 am

lookzcustoms wrote:installed spacers, will take better pics today

after

Any rubbing? Have you done the PWM? Tire size?

Do you want to buy a set of fender flares?

Post by **Adam** » Wed Mar 12, 2014 10:16 am

Put my 33's back on. Forgot about the wobble they cause. Really need to get those tire beads soon.

I took a pic next to this xterra lol

Post by **the x kid** » Wed Mar 12, 2014 4:33 pm

So you got your lift on then? Look Good.

Post by **lookzcustoms** » Thu Mar 13, 2014 12:33 pm

Miner wrote:
Any rubbing? Have you done the PWM? Tire size?

Do you want to buy a set of fender flares?

i still got the stock tires on

i want fender flares
http://www.bushwacker.com/fender-flares ... 4-70907-02

Post by **Scotto** » Thu Mar 13, 2014 1:23 pm

New driver side door hinges.

Thanks, Mike! You rock.

Sent from my iThingy.

Post by **Miner** » Wed Mar 19, 2014 12:02 pm

Oil changed and Ambient Air Temperature Sensor replaced in the V70, now I need to get all the readiness checks to go "ready" for the e-test.

Order placed to Rock Auto for the Maxima, Y / Flex Pipe, Rotors and Pads, ABS Sensor, and associated hardware. Turns out my truck and trailer / heave mechanic soon to be brother in law got a little carried away cleaning up the rotors... 3 of 4 will not pass safety.

Post by **Jayman** » Wed Mar 19, 2014 12:33 pm

Miner wrote:Oil changed and Ambient Air Temperature Sensor replaced in the V70, now I need to get all the readiness checks to go "ready" for the e-test.

Order placed to Rock Auto for the Maxima, Y / Flex Pipe, Rotors and Pads, ABS Sensor, and associated hardware. Turns out my truck and trailer / heave mechanic soon to be brother in law got a little carried away cleaning up the rotors... 3 of 4 will not pass safety.

Doh!

Post by **klbeans** » Wed Mar 19, 2014 4:56 pm

Ordered HD clutch kit from Marlin Crawler along with short shifter. New shifter & transfer case knobs on their way along with Grant steering wheel. Xmas in March.

Now waiting on warmer weather to start taking the clutch apart.

Post by **Miner** » Wed Mar 19, 2014 5:12 pm

Jayman wrote:
Miner wrote:Oil changed and Ambient Air Temperature Sensor replaced in the V70, now I need to get all the readiness checks to go "ready" for the e-test.

Order placed to Rock Auto for the Maxima, Y / Flex Pipe, Rotors and Pads, ABS Sensor, and associated hardware. Turns out my truck and trailer / heave mechanic soon to be brother in law got a little carried away cleaning up the rotors... 3 of 4 will not pass safety.
Doh!

Yeah turns out that there are more differences between the 2001 and the 2003 than we would have thought. 3.0l vs 3.5l, Auto vs Manual... interior changes, headlights are different, cats and exhaust are different, abs sensors are different...

Post by **lookzcustoms** » Wed Mar 26, 2014 5:36 pm

washed today and new tires on

Post by **PiDGE** » Fri Mar 28, 2014 2:06 pm

Lookin bad arse ^^ nice job dude. 5000km Oil change and oil gauge sender pressure thingie

Post by **Miner** » Mon Mar 31, 2014 8:55 am

New rotors and pads, replaced wheel speed sensor to clear all the ABS faults, with an oil change on the 01 Maxima. Decided to have the shop tackle the Y-Pipe / Flex Pipe with the front ball joints and the safety. I figured the shop would have an better go at it and it would save time... now they're swamped and it will be Wednesday or Thursday... we just can't win with this car.

Post by **PiDGE** » Mon Mar 31, 2014 1:10 pm

New wheel bearings....again. Seems I got some aftermarket ones and they (the wire in both) broke in the same spot. All is good and 4x4 working again. Thanks again for the diognostic.

Canadian Nissan Truck Club

What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Re: What did you do to your rig today?

Connect with your social network account