What did you do to your rig today?

Post by **Bow_Tied** » Thu Oct 13, 2011 10:45 pm

Fyrtowr wrote:
Bow_Tied wrote:^ OCD?
Nope - just bored.

Next time you are bored, come rake my leaves. Just sayin'.

reinstalled the CB last night, but I think I will redo it again after the weekend.

Post by **studum** » Fri Oct 14, 2011 9:19 am

Bow_Tied wrote:reinstalled the CB last night, but I think I will redo it again after the weekend.

OCD?

Post by **Bow_Tied** » Fri Oct 14, 2011 9:39 am

YES!

Post by **Morpheus** » Sat Oct 15, 2011 11:17 am

Broke a front swaybar link...

Post by **PiDGE** » Sat Oct 15, 2011 6:27 pm

Good luck Mike finding one of those

Post by **Jayman** » Sat Oct 15, 2011 7:42 pm

Nothing to the truck, but I seafoamed the Maxima, and then changed the oil.

Post by **studum** » Sun Oct 16, 2011 11:32 am

Friday: changed the bushings (OEM plastic) in my original IA
Yesterday: Met up with Scott, drank some beer and picked up an IA brace and spare IA he had laying around. Plan is to rebuild his spare as it showed less wear than mine did when I took it apart, and install with the IA brace. Might even go for the brass bushings in the setup with the IA brace.

Post by **Nismojunky** » Sun Oct 16, 2011 12:51 pm

the brass bushings from bandit 4x4 are sweet huge difference

Post by **Adam** » Sat Oct 22, 2011 6:31 pm

Went and fully inspected this today, gotta go the the dmv or w/e on Monday. Picking it up probably the end of the week.

Post by **Jayman** » Sat Oct 22, 2011 8:11 pm

adamzan wrote:Went and fully inspected this today, gotta go the the dmv or w/e on Monday. Picking it up probably the end of the week.

Familiar looking truck...

Post by **Snafu** » Sun Oct 23, 2011 9:37 am

Post by **Nd4SpdSe** » Sun Oct 23, 2011 7:35 pm

Made brackets for my light to light up the spare tire lowering bar socket and mounted my battery isolator.

Post by **LGM** » Mon Oct 24, 2011 6:19 pm

Installed my new (to me) Pioneer deck. (Thanks Stadum

)

Post by **studum** » Tue Oct 25, 2011 1:01 pm

LGM wrote:Installed my new (to me) Pioneer deck. (Thanks Stadum )

Who's Stadum? Lol, no prob Jay. Did you get it setup with the CB the way you wanted? Also I found the case for the faceplate that you were so enthusiastic about

. If you want it let me know, otherwise I'll toss it in with this week's trash. It was hiding in my driver's door under all my gas receipts.

Post by **LGM** » Tue Oct 25, 2011 5:09 pm

<ahem> Studum

Sure, hold on to it and I'll grab it off you sometime soon.

Had to mess around a bit with the CB to get it to fit but it looks decent, better than the hack-job I did before

Now if I could just figure out how to set the clock....

Post by **01R50** » Tue Oct 25, 2011 5:29 pm

adamzan wrote:Went and fully inspected this today, gotta go the the dmv or w/e on Monday. Picking it up probably the end of the week.

Another one?

Did you sell all the other trucks yet?

Post by **Adam** » Wed Oct 26, 2011 10:25 am

Sold my parts truck to a guy for 300 bucks and my friend says he wants to buy the gray one for a winter beater for 500 (minus the bumper lifts and tires of course). After I sell the brand new tires on the white truck I'll have made money haha. Also sending the white one to a body shop to get 1 rust spot I found fixed and the rear tailgate straightened.

Post by **Nd4SpdSe** » Thu Oct 27, 2011 5:37 pm

Haven't really had the net for a while, but here's the light I put in Monday to be able to see the damn crank for the spare tire, with the new assembly picked up from Bender at AW and installed last week

Post by **Adam** » Thu Oct 27, 2011 11:39 pm

Now that right there is a good idea!

Post by **Nd4SpdSe** » Sat Oct 29, 2011 7:43 pm

I've almost got my dual battery system in. Goth both batteries in, the solenoid/isolator mounted but only had enough wire to hook up the main battery.

Canadian Nissan Truck Club