FFS small hole turned out to be big
-
- Don't follow me, you wont make it.
- Posts: 1194
- Joined: Mon Jun 16, 2008 12:18 am
- Reactions score: 0
- Location: Brantford Canada
- Make/Model: Nissan Titan
- Year: 2006
- Tim's: Double cream
FFS small hole turned out to be big
well i knew it had a hole from what i could see it looked to be 6x6 but no its 12X24 1/2 so will this pass a safty if i rivit some sheet metal into it and then cover that in a fiberglass patch kit?
-
- Wrenchhead
- Posts: 443
- Joined: Sun Jun 01, 2008 9:33 am
- Reactions score: 0
- Location: Petawawa/Cambridge
- Make/Model: Jeep Liberty Sport
- Year: 2008
- Tim's: XL DD with milk
Re: FFS small hole turned out to be big
As long as exhaust gases can not enter the vehicle, it should pass.
2002 Nissan Xterra SE SOLD
2008 Jeep Liberty Sport
1988 Volkswagen Cabriolet
2008 Jeep Liberty Sport
1988 Volkswagen Cabriolet
-
- Premium Member
- Posts: 878
- Joined: Sun Jun 01, 2008 7:49 pm
- Reactions score: 0
- Location: Brantford
- Make/Model: SAS Xterra
- Year: 2000
Re: FFS small hole turned out to be big
Rivets will definitely pass, as long as exhaust gases cant get in. Go to home depot, get some construction adhesive for non-porous materials (in a caulking tube) and some fiberglass reinforced roofing tar (in a small tin). Cut out all the rust, fit your new sheet metal. Glue it in place with the construction adhesive...it will act as a seam sealer. Drill and rivet the sheet-metal in place. Then use the fiberglass reinforced roofing tar, and cover the seams on both sides. That'll make it super water resistant and prevent that part from continuing to rust out and get bigger. Throw down some plastic cling wrap or wax paper down over the tar before laying down your carpet. The tar is usually pretty odourless, so don't worry about that.
If you need a hand, let me know, I'm local.
If you need a hand, let me know, I'm local.
-
- Wrenchhead
- Posts: 443
- Joined: Sun Jun 01, 2008 9:33 am
- Reactions score: 0
- Location: Petawawa/Cambridge
- Make/Model: Jeep Liberty Sport
- Year: 2008
- Tim's: XL DD with milk
Re: FFS small hole turned out to be big
Yeah I am a short trip down the road too, let me know if you need some help.
-Tom-
-Tom-
2002 Nissan Xterra SE SOLD
2008 Jeep Liberty Sport
1988 Volkswagen Cabriolet
2008 Jeep Liberty Sport
1988 Volkswagen Cabriolet
- Morpheus
- Moderator
- Posts: 4318
- Joined: Wed Apr 09, 2008 8:42 am
- Reactions score: 0
- Location: Cambridge
- Make/Model: Xterra
- Year: 2003
- Tim's: 3x3
- Contact:
Re: FFS small hole turned out to be big
That rule only applies to sheet metal, and if there's any jagged edges it could be failed on that alone.lowridah313 wrote:As long as exhaust gases can not enter the vehicle, it should pass.
There can't be any rust holes in the frame or structural supports.
- Snafu
- Moderator
- Posts: 4761
- Joined: Sun Jun 01, 2008 9:51 am
- Reactions score: 1
- Location: Fergus-Orangeville
- Make/Model: Xterra S
- Year: 2007
- Tim's: Double milk - no sugar
Re: FFS small hole turned out to be big
Is this a hole in the floor or body panel? If it is a body panel then you might want it to look a little more decent than a patch.
I would cut out the rust to a good edge then take a piece of sheet metal and match the hole (size and shape) as best you can. Use an etching primer, primer and paint (both sides) to help prevent rust happening again. Once everything is dry then I would rivet one corner then form the new piece as you go along (I would rivet where ever the new sheet won't stay down or every 2"). After it is all in place, I would either spread caulking and then undercoating on both sides if this is a floor patch or use fiberglass/bondo/primer/pain to clean up the edges and rivets if this is a body patch.
Just my $0.02
I would cut out the rust to a good edge then take a piece of sheet metal and match the hole (size and shape) as best you can. Use an etching primer, primer and paint (both sides) to help prevent rust happening again. Once everything is dry then I would rivet one corner then form the new piece as you go along (I would rivet where ever the new sheet won't stay down or every 2"). After it is all in place, I would either spread caulking and then undercoating on both sides if this is a floor patch or use fiberglass/bondo/primer/pain to clean up the edges and rivets if this is a body patch.
Just my $0.02
- Simon
- Moderator
- Posts: 4087
- Joined: Sat Feb 02, 2008 10:42 am
- Reactions score: 0
- Location: Brampton, Ontario
- Make/Model: Nissan Maxima
- Year: 2011
- Tim's: XL COFFEE ! 1M 1S
- Contact:
Re: FFS small hole turned out to be big
I believe it's the floor. Standard WD21 Pathfinder hole under the driver's right foot.
"CAUTION: Hot shovel in close proximity to my person"-Bow_Tied
- Bender
- Premium Member
- Posts: 2029
- Joined: Sun Feb 03, 2008 9:06 pm
- Reactions score: 0
- Location: Fergus
- Make/Model: Nissan Sentra SER
- Year: 2011
- Tim's: Mcdonalds coffee
Re: FFS small hole turned out to be big
Been there, fixed that.Simon wrote:I believe it's the floor. Standard WD21 Pathfinder hole under the driver's right foot.
-
- I've used 4-lo
- Posts: 535
- Joined: Wed Apr 09, 2008 5:01 pm
- Reactions score: 0
- Location: KW
- Make/Model: Lexus LX
- Year: 2006
Re: FFS small hole turned out to be big
Have I said sorry lately?Bender wrote:Been there, fixed that.Simon wrote:I believe it's the floor. Standard WD21 Pathfinder hole under the driver's right foot.
-
- Don't follow me, you wont make it.
- Posts: 1194
- Joined: Mon Jun 16, 2008 12:18 am
- Reactions score: 0
- Location: Brantford Canada
- Make/Model: Nissan Titan
- Year: 2006
- Tim's: Double cream
Re: FFS small hole turned out to be big
yep its the floor pannel... thanks for all your replys, im going to get to it this weekend. and if i get a filber glass patch kit and do the whole underbody (floor) will that help stop it from rusting ? and can you undercaot the fiblerglass
-
- Wrenchhead
- Posts: 443
- Joined: Sun Jun 01, 2008 9:33 am
- Reactions score: 0
- Location: Petawawa/Cambridge
- Make/Model: Jeep Liberty Sport
- Year: 2008
- Tim's: XL DD with milk
Re: FFS small hole turned out to be big
Yes you can. Just grab a spraycan of rubberized undercoat.
2002 Nissan Xterra SE SOLD
2008 Jeep Liberty Sport
1988 Volkswagen Cabriolet
2008 Jeep Liberty Sport
1988 Volkswagen Cabriolet
-
- Don't follow me, you wont make it.
- Posts: 1194
- Joined: Mon Jun 16, 2008 12:18 am
- Reactions score: 0
- Location: Brantford Canada
- Make/Model: Nissan Titan
- Year: 2006
- Tim's: Double cream
Re: FFS small hole turned out to be big
alright :d thanks for your help and for offering your services i got a friends whos 50 whos done anuto body all his life hes away for a few days so i jsut want to get everything rdy for when he gets back
-
- Don't follow me, you wont make it.
- Posts: 1194
- Joined: Mon Jun 16, 2008 12:18 am
- Reactions score: 0
- Location: Brantford Canada
- Make/Model: Nissan Titan
- Year: 2006
- Tim's: Double cream
Re: FFS small hole turned out to be big
well after i gut out all the bad it was around 42/36 i got a peice of sheet metal fiberglass patch and undercoat looks brand new lol thx for all your help now to install the new speakers and reinstall the interior