Pathy Question
- Miner
- Don't follow me, you wont make it.
- Posts: 3375
- Joined: Sun Jun 01, 2008 1:19 am
- Reactions score: 0
- Location: Kingston
- Make/Model: Cummins 2500 HD
- Year: 2012
- Tim's: McD's 3C1S
Pathy Question
I was looking at used Pathfinders and Frontiers on Auto Trader for a future project truck (probably just a pipe dream). If it was to happen what years did the Pathfinder have a full frame? And are there certain years/options to avoid in the Pathfinder? Frontier?
Cummins - Zone, BD, AFE, Yokohama, Bestop, Access, VisonX, H&S
Simon wrote:It's not like the membership voted under control of a heavy hand...
Dammit, I've said too much...I'll have to ban you now
- Simon
- Moderator
- Posts: 4087
- Joined: Sat Feb 02, 2008 10:42 am
- Reactions score: 0
- Location: Brampton, Ontario
- Make/Model: Nissan Maxima
- Year: 2011
- Tim's: XL COFFEE ! 1M 1S
- Contact:
Re: Pathy Question
The full frame Pathfinders were from 87-95, then again from 05+. The 05+ should be avoided, simply because they have independant suspension front and back.
With the WD21 (87-95) Pathys, look for frame rust. That's the #1 killer of these things. Tap around with a hammer to check it out, especially over the rear wheels.
I've heard that the earlier models (87-90) were better than the later ones, as Nissan switched steel suppliers around that time. The later ones can take quite a bit of work to keep the frame strong enough to handle the stresses of offroading.
With the Frontiers, they're basically the same as the 00-04 Xterras. Same suspension, motor, tranny, everything.
With the WD21 (87-95) Pathys, look for frame rust. That's the #1 killer of these things. Tap around with a hammer to check it out, especially over the rear wheels.
I've heard that the earlier models (87-90) were better than the later ones, as Nissan switched steel suppliers around that time. The later ones can take quite a bit of work to keep the frame strong enough to handle the stresses of offroading.
With the Frontiers, they're basically the same as the 00-04 Xterras. Same suspension, motor, tranny, everything.
"CAUTION: Hot shovel in close proximity to my person"-Bow_Tied
- Snafu
- Moderator
- Posts: 4761
- Joined: Sun Jun 01, 2008 9:51 am
- Reactions score: 1
- Location: Fergus-Orangeville
- Make/Model: Xterra S
- Year: 2007
- Tim's: Double milk - no sugar
Re: Pathy Question
Two things to watch for when buying a frontier (and xterra). First is a cracked exhaust manifold (mine is cracked on the passenger side). With the SC version watch for cracks in the blower housing (mine is not SC so can only relate from a person who had a SC version). Otherwise I love my truck
One other thing to look for are the shields on the 4 cats. They like to rust off and either fall off or just sit there rattling away. More annoyance than anything unless you drive over a shield that has fallen off (they are pretty thick).
One other thing to look for are the shields on the 4 cats. They like to rust off and either fall off or just sit there rattling away. More annoyance than anything unless you drive over a shield that has fallen off (they are pretty thick).
- Miner
- Don't follow me, you wont make it.
- Posts: 3375
- Joined: Sun Jun 01, 2008 1:19 am
- Reactions score: 0
- Location: Kingston
- Make/Model: Cummins 2500 HD
- Year: 2012
- Tim's: McD's 3C1S
Re: Pathy Question
Thanks I'll narrow my search and make sure to perform a thorough frame and engine inspection, if I ever go through with it.Simon wrote:... WD21 (87-95) Pathys...
Cummins - Zone, BD, AFE, Yokohama, Bestop, Access, VisonX, H&S
Simon wrote:It's not like the membership voted under control of a heavy hand...
Dammit, I've said too much...I'll have to ban you now
-
- Lugnut
- Posts: 58
- Joined: Sun Jun 01, 2008 11:03 am
- Reactions score: 0
- Location: London
- Make/Model: Xterra SE
- Year: 2003
- Tim's: Strawberry Vanilla Donut
Re: Pathy Question
Check for broken tie rod ends if you look at a 91. lol.
J/k. I only had mine snap because I was doing my best Clark Kent imitation that day.
Seriously though if I hadn't been T-boned I would still be driving this. You'll be very happy with it.
J/k. I only had mine snap because I was doing my best Clark Kent imitation that day.
Seriously though if I hadn't been T-boned I would still be driving this. You'll be very happy with it.
- Miner
- Don't follow me, you wont make it.
- Posts: 3375
- Joined: Sun Jun 01, 2008 1:19 am
- Reactions score: 0
- Location: Kingston
- Make/Model: Cummins 2500 HD
- Year: 2012
- Tim's: McD's 3C1S
Re: Pathy Question
Nice, too bad she broke.
Cummins - Zone, BD, AFE, Yokohama, Bestop, Access, VisonX, H&S
Simon wrote:It's not like the membership voted under control of a heavy hand...
Dammit, I've said too much...I'll have to ban you now