Canadian Nissan Truck Club

you guys have done a fantastic job keeping this going strong .... i as well have been absent -totally for some time ... bloody life getting in the way ...sounds like AW was a success again - deb and i were actually talking about the trips we took with the group and how much fun they were . morpheus ...

Mine has been plugged just about daily in since the day i bought it years ago.
I'd say not an issue. in two different cars i have never felt a loss of anything.

Gino - do you ever blink ???

Is it just me or does anyone else find this creepy?

U calling me a Knucklehead !!!?!?!?!?!?!?

Gino .... Don't make me come over there.

Yeah those are GREAT.
The Nkon equiv is a F-1.4 50mm Prime. The plastic body version is <>$120
I have had one for years, and I love it.

Debbie and I use 2 Nikon D700's and a D40 for our Wedding Photography Bis We have parted ways with our 'old' D200 - traded it in on one of the D700's Yes the D90 is a replacement for the D80, As the D300 replaced the D200 and the D50 replaced the D40 The D90 was the first to add Video to a Nikon DSL...

My 2 cents... Some say that if you locate the plate under the tire carrier the 407 cameras may not be able to see it but will still be visible whilst driving behind the truck. This is true - 6 years driving my Chevy ZR2 with the tire out there and the plate in the stock location centered on the rea...

Pouting -

at least i sold mine, i did it to myself.

I can't imagine it dying on me

Medic
Today sitting in the 'fast' lane on the 403 <> 7:30am

Deb and I wizzed by in the Altima using the HOV lane.

Hi Patrick!!!!!

it will also prevent the switch gear from burning out due to the higher current loads.
Allows for much smaller and less expensive switch gear to be used, and less risk of an electrical meltdown behind the dash.

when i did mine, I used a fan assy from an old Escape i relayed the larger diameter fan of the pair (the Escapes had a dual fan set up at the time) it into the Ignition circuit so it was automatic on/off with the motor, and then relayed the second on in to the A/C compressor circiut so that it would...

There is also this plce in Mississauga.

Active Starters & Alternator Rebuilder IncActive Starters & Alternator Rebuilder Inc
Place page
2179 Dunwin Dr
Mississauga, ON L5L 1X2
(905) 828-6825

I have used him probably a dozen times over the years. always good quality work.

both those trims are bolted on from the inside. once you remove the inner liners you will be able to get the outer pieces off.. The bigger problem is the rust around the rear glass. If it apears that big outside the trim/glass it is a safe bet it is almost similar sized under the trim/glass. Rust li...

yeah it must be, this is the only other thing i could see you "driving" http://us.123rf.com/400wm/400/400/jaminsonmoses/jaminsonmoses1008/jaminsonmoses100800016/7544887-rodent-in-a-hamster-ball-wanting-to-go-down-gopher-hole-so-close-but-so-far-away.jpg better put 'er in 4-lo for that mud...

Figured i would just bring this one back to life, rather than start another thread:

Mike, Jay, Dan -- Thanks for fixing up the Altima yesterday. Exhaust sounds WAY better, leak is gone!

:Whoot:

happy birthday Mike, thanks for the help over the years.

it would have to be hydraulic drive. I simply cant imagine any other soloution

simply one word .....

WOW

Oh I want to laugh. I so want to Laugh

Dam you Corporate America!

Dam you!!!!!!!!!